Paint Calculator: Walls and Ceiling
Paint calculator: walls and ceiling of one room, minus doors and windows, in liters or US gallons for any number of coats, rounded up to whole cans.
Paint needed
- In US gal
- 1.8 US gal
- Wall area to paint
- 34.1 m²
- Doors and windows deducted
- 3.4 m²
- Cans of 4 L
- 2
- Left over
- 1.18 L
How to use the Paint Calculator
- Measure the room's length, width and wall height, and enter them in meters or feet.
- Enter how many doors and windows the room has; each one is deducted at a standard size.
- Switch on the ceiling if you are painting it too, and set the number of coats.
- Copy the coverage and can size from the paint can, and optionally the price per can.
- Read the paint needed, the number of cans to buy, what will be left over and the cost.
Formula
Paint = (2 × (L + W) × H − doors − windows + ceiling) × coats ÷ coverage
Where:
- L, W
- Room length and width, in meters or feet
- H
- Wall height from floor to ceiling, in meters or feet
- doors, windows
- Openings deducted: 1.9 m² (20 ft²) per door and 1.5 m² (15 ft²) per window
- ceiling
- L × W when the ceiling is included, otherwise 0
- coats
- Number of coats, usually 2 (3 over a dark or strong color)
- coverage
- Spread rate of one coat from the can, in m² per liter or ft² per US gallon
Cans = paint ÷ can size, rounded up. The spread rate assumes a smooth, sealed surface; rough, porous or new plaster can take 20% to 50% more. 1 US gallon = 3.785411784 liters.
Worked example
A bedroom is 14 ft × 12 ft with 8 ft walls, one door and two windows. You want two coats of a paint that covers 350 ft² per gallon and costs $45 a gallon.
- Wall area: 2 × (14 + 12) × 8 = 416 ft².
- Openings: one door (20 ft²) and two windows (2 × 15 = 30 ft²) = 50 ft², leaving 416 − 50 = 366 ft².
- Paint: 366 × 2 coats ÷ 350 ft²/gal ≈ 2.09 gallons.
- Gallon cans: 2.09 rounds up to 3 cans, so about 0.91 gallon is left for touch-ups.
- Cost: 3 × $45 = $135.
You need about 2.09 gallons of paint, which means buying 3 one-gallon cans for $135.
How much paint for the walls of a room
Most people grab two cans, hope for the best, and make a second trip to the store halfway through the second coat. A few measurements replace the guess. People call the same job a paint estimate, a paint quantity or, in the UK, working out how many litres of emulsion to buy.
- Length and width. Measure along the floor, wall to wall. Baseboards and skirting do not matter at this level of accuracy.
- Wall height. Measure from the floor to the ceiling, not to a picture rail unless you are only painting below it.
- Openings. Count the full-size doors and windows. Each door deducts about 0.9 m × 2.1 m (1.9 m²), or 3 ft × 6 ft 8 in (20 ft²), and each window 1.5 m² (15 ft²). A patio door or a large picture window is closer to two standard openings, so count it twice.
Only the perimeter matters for the walls: 2 × (L + W) is a shortcut for a rectangular room. A common slip is to use the floor area instead. A 4 m × 4 m room has 16 m² of floor but, with 2.5 m walls, 40 m² of wall.
Adding the ceiling
Switch the ceiling on and its area, length × width, is added to the walls before the coats are applied.
Worked example: walls and ceiling in liters. A living room is 5 m × 4 m with 2.6 m walls, two doors and two windows. The paint covers 12 m² per liter and comes in 2.5-liter tins.
- Walls: 2 × (5 + 4) × 2.6 = 46.8 m².
- Openings: 2 × 1.9 + 2 × 1.5 = 6.8 m², leaving 40 m² of wall.
- Ceiling: 5 × 4 = 20 m², so the total is 60 m².
- Paint for two coats: 60 × 2 ÷ 12 = 10 liters, exactly four 2.5-liter tins.
There is a catch. Ceilings are normally painted in a flat white while the walls get a color, so in practice you buy two products. The walls need 40 × 2 ÷ 12 ≈ 6.67 liters (three tins) and the ceiling 20 × 2 ÷ 12 ≈ 3.33 liters (two tins), five tins in total instead of four. When the paints differ, run it once with the ceiling off and once for the ceiling alone.
Coverage per liter and per gallon
The coverage, or spread rate, is printed on the can, usually as a range such as "10–12 m²/L" or "350–400 sq ft per gallon". It describes one coat on a smooth, sealed surface, so use the lower end for a realistic estimate. Things that cut it:
- Porous surfaces such as new plaster, bare drywall, brick and concrete drink the first coat.
- Textured walls, including popcorn ceilings, stipple and roughcast render, have far more real surface than their flat size. Allow 20% to 50% more paint.
- Gloss and semi-gloss show every thin patch and often need an extra coat on large areas.
Mind which gallon a guide uses. A US gallon is 3.785 liters; an imperial gallon, sometimes quoted in older British guides, is 4.546 liters. Outside the US, paint is sold in liters (1, 2.5, 4, 5, 10 or 20 L), so enter your can size in liters there.
One coat or two
The coverage on the can is for one coat, and two coats double the paint. Two is the normal plan for interior walls; covering a deep red with a pale gray can take three, or a tinted primer followed by two.
When you need primer. Bare plaster, new drywall, patched areas, stains and glossy old finishes need a primer or a diluted mist coat first. Primer is a separate product with its own spread rate, often only 6 to 9 m² per liter on porous surfaces, so work it out separately: run the room again with one coat and the primer's coverage.
If you need more than one can of a tinted color, mix them together in a bucket before you start; small differences between batches show on a flat wall. Keep the leftover sealed and labeled with the room name for touch-ups.
Assumptions
Each run covers the interior walls, and optionally the ceiling, of one rectangular room with walls of equal height. Doors and windows are deducted at the standard sizes above. Sloped ceilings, single feature walls and several rooms need separate runs or a hand adjustment. Primer, trim, doors, cabinets and exterior walls are not included, and there is no waste allowance beyond rounding up to whole cans. If the result sits just under a whole can, or the wall is rough, buy one more small can. Follow the manufacturer's instructions for drying, recoating and preparation.
Frequently asked questions
How many gallons of paint for a 12x12 room?
With 8 ft walls, one door and one window, the walls come to 2 × (12 + 12) × 8 = 384 ft², less 35 ft² of openings, so 349 ft². Two coats at 350 ft² per gallon need 349 × 2 ÷ 350 ≈ 1.99 gallons, so buy 2 gallons. Adding the 144 ft² ceiling takes about 0.82 gallon more for two coats.
How many liters of paint for a room?
Add up the wall area (the room's perimeter times its height), subtract doors and windows, multiply by the number of coats and divide by the coverage on the can. A 4 m × 3.5 m room with 2.5 m walls, one door and one window has 34.1 m² of wall, so two coats at 10 m² per liter need about 6.82 liters.
How much does a gallon of paint cover in square feet?
Most interior wall paints sold by the gallon cover roughly 350 to 400 ft² per US gallon per coat on a smooth, sealed wall, which is about 8.6 to 9.8 m² per liter. Paints sold in liters often quote 10 to 12 m² per liter. Primers, textured paints and masonry paints cover less, sometimes only 5 to 8 m² per liter, so always use the figure printed on your can.
Do I need two coats of paint?
Usually, yes. One coat rarely gives an even color, especially with a big color change, and a second coat evens out the sheen and covers thin spots. Plan for three coats when covering a dark color with a light one, or prime first and then apply two finish coats.
Should I subtract doors and windows when estimating paint?
Yes for full-size doors and windows; that is why this calculator deducts 1.9 m² (20 ft²) per door and 1.5 m² (15 ft²) per window. Skip the deduction for very small openings, because cutting in around them uses extra paint anyway.
How much paint do I need for a ceiling?
A flat ceiling's area is simply length × width. A 4 m × 3.5 m ceiling is 14 m², so two coats at 10 m² per liter need 2.8 liters. Ceilings are often painted in a separate flat white, so check the ceiling row and buy that paint separately.
Related calculators
- Tile CalculatorA tile calculator with spacing for a floor or wall: enter the area, tile size and grout joint to get the tiles and boxes to buy.
- Flooring CalculatorFlooring calculator: cost of the whole boxes you buy, plus the waste for your layout, leftover area and baseboard length for one room.
- Brick CalculatorA brick calculator with mortar for any straight wall: bricks to buy after doors and windows, plus the mortar, cement bags and sand it takes.
- Concrete CalculatorA concrete calculator in cubic meters and cubic yards for a slab, footing, wall or round post, with premix bags, site-mix materials and cost.
- Area CalculatorArea calculator: square feet, square meters or six other units for 12 shapes, from rectangles and circles to a triangle with three known sides.
- Surface Area CalculatorLateral surface area calculator for cylinders, cones, prisms and pyramids, with the total area, slant height and volume of 11 solids.
Last updated: