Skip to content

Brick Calculator with Mortar, Cement and Sand

A brick calculator with mortar for any straight wall: bricks to buy after doors and windows, plus the mortar, cement bags and sand it takes.

Units
m

m

m²

A door is about 1.9 m², a window about 1.5 m².

Length × width × height, without mortar.

mm

10 mm is standard.

%

5% for most walls; 10% for cut-heavy work.

Wall thickness

Only changes the cement and sand rows.

In USD, to estimate the cost of the bricks.

Bricks needed

934 bricksincluding 5% waste
Bricks per m²
59.26
Net wall area
15 m²
Bricks laid (no waste)
889
Mortar volume
0.264 m³
Cement (50 kg bags)
2 (72 kg)
Sand
0.301 m³

How to use the Brick Calculator

  1. Enter the length and height of the wall, and the area of any doors or windows in it.
  2. Choose your brick size, or pick Custom size and type the length, width and height of one brick.
  3. Set the mortar joint, the wall thickness (half brick or one brick) and a waste allowance.
  4. Pick a mortar mix to see the cement and sand, and add a price per brick to estimate the cost.

Formula

N = (L × H − A) × w ÷ ((l + j) × (h + j)) × (1 + waste ÷ 100)

Where:

N
Bricks to buy, rounded up to a whole brick
L, H
Wall length and height (m or ft)
A
Area of doors, windows and other openings (m² or ft²)
w
Wythes (skins): 1 for a half-brick wall, 2 for a one-brick wall
l, h
Length and height of one brick, without mortar
j
Mortar joint thickness, in the same unit as the brick
waste
Allowance for cut and broken bricks, in percent

Mortar = net area × wall thickness − volume of the bricks. Dry materials = mortar × 1.33; cement is taken at 1,440 kg/m³. One-brick walls are treated as two skins; header courses are not modeled separately.

Worked example

A garden wall is 30 ft long and 4 ft high, built as a single skin of US modular bricks (7⅝ × 3⅝ × 2¼ in) with ⅜ in joints, 1:5 mortar and 5% waste. The bricks cost $0.80 each.

  1. Wall area: 30 × 4 = 120 ft².
  2. One brick plus its joints covers (7.625 + 0.375) × (2.25 + 0.375) = 8 × 2.625 = 21 in², so there are 144 ÷ 21 ≈ 6.857 bricks per ft².
  3. Bricks laid: 120 × 6.857 ≈ 822.9, so 823 bricks.
  4. With 5% waste: 822.857 × 1.05 = 864 bricks.
  5. Mortar: 120 ft² × 3.625 in thick, minus the bricks' own volume, leaves about 6.64 ft³ of mortar, which needs about 132 lb of cement (2 × 94 lb bags) and 7.35 ft³ of sand in a 1:5 mix.
  6. Cost: 864 × $0.80 = $691.20.

Order 864 bricks (about $691.20), 2 bags of cement and roughly 7.4 ft³ (0.27 yd³) of sand.

Bricks per square meter and per square foot

Using the wrong brick size is the biggest single source of error in a count. Each brick in the wall occupies its own face plus one joint along its end and one along its top, so a brick l long and h high with joints j thick covers (l + j) × (h + j) of wall. Dividing one square meter or square foot by that area gives the count for a single skin. With the usual joint for each format (10 mm, or ⅜ in for US bricks), the presets work out as follows:

Brick (length × width × height)Per m²Per ft²
UK / EU standard, 215 × 102.5 × 65 mm59.35.5
US modular, 7⅝ × 3⅝ × 2¼ in73.86.9
US standard, 8 × 3¾ × 2¼ in70.56.5
Australian standard, 230 × 110 × 76 mm48.44.5
Modular, India, 190 × 90 × 90 mm504.6
Traditional South Asian, 240 × 115 × 70 mm504.6

Local kilns often produce bricks a few millimeters off their nominal size. If you have bricks on hand, measure ten in a row, divide by ten and enter the result under Custom size. The joint matters too: going from 10 mm to 12 mm on UK bricks drops the count from 59.3 to 57.2 per m², but adds mortar.

How much mortar a wall needs

Mortar is everything in the wall that is not brick. The tool takes the wall volume (net area × wall thickness) and subtracts the volume of the bricks laid. Loose sand and cement contain air and shrink when mixed with water, so the dry materials are about one third more than the finished mortar: the wet volume is multiplied by 1.33. In the US, mortar is often bought premixed in bags; the results give cement and sand, so for premix divide the mortar volume by the yield printed on the bag.

Cement and sand for brickwork

The dry volume is split by the mix you pick: 1:3 for work below ground, 1:4 for exposed or load-bearing walls, 1:5 for general walls and 1:6 for internal partitions. Cement is weighed at 1,440 kg per cubic meter and rounded up to whole bags of 50 kg in metric or 94 lb in imperial.

Worked example: an internal partition with a door. A partition is 6 m long and 2.7 m high, with a door opening of 1.9 m². It is half a brick thick in traditional 240 × 115 × 70 mm bricks with 10 mm joints, 1:6 mortar and 5% waste.

  1. Gross area: 6 × 2.7 = 16.2 m². Net area: 16.2 − 1.9 = 14.3 m².
  2. Face per brick: 0.25 × 0.08 = 0.02 m², so exactly 50 bricks per m².
  3. Bricks laid: 14.3 × 50 = 715. With 5% waste: 750.75, so order 751 bricks.
  4. Wall volume: 14.3 × 0.115 = 1.6445 m³. Brick volume: 715 × (0.24 × 0.115 × 0.07) = 1.38138 m³. Mortar: about 0.263 m³.
  5. Dry materials: 0.263 × 1.33 ≈ 0.350 m³. Cement is 1/7: about 72 kg, or 2 bags of 50 kg. Sand is 6/7: about 0.30 m³.

Sand is cheap and some is always lost on the ground, so many builders round it up to the next half cubic meter or quarter yard.

Half-brick and one-brick walls

A half-brick wall is a single skin, the 4-inch or 5-inch wall of South Asian sites. A one-brick wall, the 9-inch or 10-inch wall, is two skins side by side. In a real bond some bricks are turned as headers, but the total per square meter stays very close to double, so the tool counts it as two stretcher skins with a joint between them. Forgetting the second skin halves the order.

Common mistakes

  • Mixing units. Switch the unit system at the top of the page instead of combining millimeter bricks with a wall measured in feet.
  • Using nominal instead of actual sizes. US catalogs sometimes list nominal sizes that already include a joint. Enter the actual brick and the joint separately, or the mortar is counted twice.
  • Deducting lintels. Subtract the full door or window opening, but not the brickwork above it, which sits within the wall's height.
  • Ignoring waste. Cuts at corners and openings plus breakage add up quickly on small jobs.

Assumptions

The wall is a straight, flat rectangle with uniform joints. Piers, columns, arches, paving and patios are outside its scope; measure gable ends or stepped walls as separate rectangles and add them. Bond patterns, headers, cavity ties and pallet counts are not modeled, and the cost covers bricks only. Mortar figures use common estimating values, so treat cement and sand as a guide. Structural walls must be designed and checked by a qualified engineer in line with your local building code.

Frequently asked questions

How many bricks per m2?

About 60 for a single-skin wall of UK/EU standard bricks (215 × 65 mm face) with 10 mm joints: 1 ÷ (0.225 × 0.075) = 59.26, rounded up in the trade to 60. A one-brick (double-skin) wall needs twice as many, about 119 per m². Larger traditional South Asian bricks (240 × 70 mm) need 50 per m² per skin.

How many bricks per square foot?

About 6.9 US modular bricks (7⅝ × 2¼ in) per square foot of single-skin wall with ⅜ in joints, using the actual brick size. Published tables often quote 6.75, which is based on the nominal 8 × 2⅔ in module (three courses in 8 inches). US standard 8 in bricks need about 6.5 per ft².

How many bricks do I need for a wall?

Multiply the wall length by its height, subtract the area of doors and windows, then divide by the face area of one brick including one joint on its end and one on its top. Multiply by 2 for a one-brick-thick wall, add 5% to 10% for waste and round up to a whole brick.

How much cement and sand do I need for brickwork?

Work out the mortar volume (wall volume minus the bricks), multiply by 1.33 to get the dry volume, then split it by the mix ratio. For a 1:6 mix, one seventh is cement and six sevenths sand. A 15 m² half-brick wall of standard UK bricks needs about 0.26 m³ of mortar: roughly 72 kg of cement (2 bags of 50 kg) and 0.30 m³ of sand.

What is the difference between a half-brick and a one-brick wall?

A half-brick wall is one brick wide, laid lengthwise: about 100 to 115 mm (4 to 4½ in) thick, often called a 4-inch or 5-inch wall and used for partitions and veneers. A one-brick wall is two bricks wide, about 215 to 240 mm (9 to 10 in), often called a 9-inch or 10-inch wall, and is used for load-bearing and boundary walls.

How much extra brick should I order?

Add about 5% for plain walls and 10% where there are many corners, piers, openings or cut bricks. Bricks from different batches can differ in color, so it is better to order enough at once than to top up later, and a few dozen spares from the same batch make repairs blend in.

Last updated: