Ohm's Law Calculator with Watts
This Ohm's law calculator with watts takes any two of volts, amps, ohms and watts and works out the other two, showing the formula for each.
Resistance (R)
- Voltage (V)
- 12 V
- Current (I)
- 2 A
- Power (P) · P = V × I
- 24 W
How to use the Ohm's Law Calculator
- Under Known values, choose the two quantities you already have, such as voltage and current.
- Enter each value and pick its unit, for example mA for milliamps or kΩ for kilohms.
- Read the first missing quantity in the result; the second appears in the list below it with the formula used.
- All four values are shown with a sensible prefix, so 0.025 A reads as 25 mA.
Formula
V = I × R · P = V × I = I² × R = V² ÷ R
Where:
- V
- Voltage (potential difference) across the component, in volts (V)
- I
- Current through the component, in amperes (A)
- R
- Resistance of the component, in ohms (Ω)
- P
- Power dissipated by the component, in watts (W)
Valid for DC circuits and for AC circuits with a purely resistive load when V and I are RMS values. Motors, transformers and electronics with reactance or a power factor below 1 need AC power formulas instead.
Worked example
A 470 Ω resistor is connected across a 9 V battery. How much current flows, and how much power does the resistor dissipate?
- I = V ÷ R = 9 ÷ 470 ≈ 0.019149 A ≈ 19.15 mA.
- P = V² ÷ R = 81 ÷ 470 ≈ 0.17234 W.
- Check: P = V × I = 9 × 0.019149 ≈ 0.1723 W.
- A standard 1/4 W (0.25 W) resistor is enough, with some margin.
About 19.15 mA flows and the resistor dissipates about 0.172 W.
Ohm's law and the power formulas
Every simple electrical circuit can be described by four numbers. Voltage (V, in volts) is the electrical push that drives charge around the loop. Current (I, in amperes) is how much charge flows past a point each second. Resistance (R, in ohms, Ω) is how strongly a component opposes that flow. Power (P, in watts) is the rate at which energy is converted, usually into heat or light.
Two relationships tie them together: V = I × R and P = V × I. With two equations and four unknowns, any two known values are enough to find the other two. Electricians often draw the result as a "power wheel" of twelve formulas. You do not need to memorize it; each one comes from substituting one equation into the other.
| To find | From V and I, or I and R, or V and R | Using power |
|---|---|---|
| Voltage V | I × R | P ÷ I, or √(P × R) |
| Current I | V ÷ R | P ÷ V, or √(P ÷ R) |
| Resistance R | V ÷ I | V² ÷ P, or P ÷ I² |
| Power P | V × I | I² × R, or V² ÷ R |
Watts to amps and amps to watts
To size a fuse, breaker or extension lead, convert an appliance's wattage to current at your supply voltage: 120 V in North America, 230 V in most other countries. For resistive loads such as heaters, kettles and toasters:
| Power | Current at 120 V | Current at 230 V |
|---|---|---|
| 100 W | 0.83 A | 0.43 A |
| 500 W | 4.17 A | 2.17 A |
| 1,000 W | 8.33 A | 4.35 A |
| 1,500 W | 12.50 A | 6.52 A |
| 2,000 W | 16.67 A | 8.70 A |
| 3,000 W | 25.00 A | 13.04 A |
Motors, compressors and switching power supplies have a power factor below 1, which this tool does not apply, so they draw more current than the table shows.
Low-voltage example: a halogen headlight bulb is rated 55 W at 12 V. Choose Power and voltage and enter both.
- Current: I = P ÷ V = 55 ÷ 12 ≈ 4.583 A.
- Hot resistance: R = V² ÷ P = 144 ÷ 55 ≈ 2.618 Ω.
That current is why headlight circuits use a relay and a fuse of around 10 A. A multimeter on the cold filament reads far less than 2.6 Ω, because tungsten's resistance rises sharply as it heats; Ohm's law gives the operating-point resistance.
Finding resistance from voltage and current
R = V ÷ I is the everyday design calculation. For an LED, subtract its forward voltage from the supply first: with 5 V, a 2 V LED and 20 mA, the resistor sees 3 V, so R = 3 ÷ 0.02 = 150 Ω, dissipating 0.06 W. Enter 3 V and 20 mA here to check. Then rate the part with headroom: many designers pick a resistor rated for at least double the calculated power.
Only ohmic parts, such as resistors and metal wire at a steady temperature, have a fixed resistance. Diodes, LEDs and transistors do not, so a single value describes only one operating point.
Units and prefixes
A sensor might draw 150 µA, a pull-up resistor might be 10 kΩ, and an electric kettle uses about 2 kW. The unit lists accept the common SI prefixes (µ, m, k, M) and rescale results automatically, so 0.0042 A appears as 4.2 mA and 2,200,000 Ω as 2.2 MΩ. Mechanical horsepower (1 hp = 745.7 W) is available for power, which helps with motor nameplates, though motors are not purely resistive. An amplifier giving 100 W into an 8 Ω speaker works out at √800 ≈ 28.28 V and √12.5 ≈ 3.536 A RMS.
Common mistakes
- Using the supply voltage instead of the voltage across the part. In a series circuit the voltage divides between components.
- Mixing milliamps with amps. It is the most common factor-of-1,000 error; select the right unit in each field instead.
- Trusting the label voltage of a battery. Batteries sag under load, so use the voltage you actually measure across the component.
- Ignoring power factor on AC. For a motor, V × I gives apparent power in volt-amperes, larger than the real power in watts.
Assumptions and safety
The tool handles one component at a time and assumes direct current, or alternating current with a purely resistive load and RMS values. It treats resistance as constant and ignores wire resistance, internal battery resistance and temperature effects. Series and parallel networks, voltage dividers, cable voltage drop and three-phase supplies are not covered. Results are for learning, design estimates and low-voltage hobby work. Mains voltage can cause serious injury or death: leave household and industrial wiring to a qualified electrician, and always follow your local electrical code.
Frequently asked questions
How do I work out Ohm's law?
Ohm's law says V = I × R: voltage equals current times resistance. Cover the quantity you want and the other two show what to do. To find current, divide voltage by resistance; to find resistance, divide voltage by current. Double the voltage across a fixed resistor and the current doubles. Georg Ohm published the law in 1827.
How do I calculate amps from watts?
Divide the power by the voltage: I = P ÷ V. A 1,500 W heater on a 120 V circuit draws 12.5 A; on a 230 V supply it draws about 6.52 A. This assumes a resistive load such as a heater, kettle or incandescent lamp. Motors and compressors also have a power factor, so they draw more current than this gives.
How do I calculate watts from volts and amps?
Multiply them: P = V × I. A device drawing 15 A from a 120 V supply uses 120 × 15 = 1,800 W, and 13 A at 230 V is 2,990 W. For AC this is exact only for resistive loads; for motors and electronics, V × I gives apparent power in volt-amperes, which is more than the real power in watts.
How do I calculate power with Ohm's law?
Start from P = V × I and substitute Ohm's law. Replacing V with I × R gives P = I² × R; replacing I with V ÷ R gives P = V² ÷ R. All three give the same answer, so use the one that matches the two values you know. The calculator picks it for you and shows it under the result.
How do I use Ohm's law to find resistance?
Divide voltage by current: R = V ÷ I. If 12 V drives 2 A through a component, its resistance is 6 Ω. Convert milliamps to amps first (or pick mA in the unit list) to avoid a factor of 1,000 error. If you know power instead, R = V² ÷ P or R = P ÷ I².
Does Ohm's law work for AC?
For purely resistive loads, yes, using RMS values for voltage and current. Inductors and capacitors add reactance, so the opposition to current becomes impedance and real power becomes V × I × power factor. This calculator does not handle reactance, power factor or three-phase supplies.
Related calculators
- Force CalculatorThis force calculator in newtons solves Newton's second law, F = m × a, for force, mass or acceleration, with each value in its own unit.
- Kinetic Energy CalculatorKinetic energy calculator: velocity, mass or energy from the other two with KE = ½mv², plus gravitational potential energy with PE = mgh.
- Speed CalculatorA speed calculator with time and distance inputs: find speed, distance or travel time from the other two, plus pace per km and per mile.
- Scientific CalculatorA free online scientific calculator in degree mode by default, with a DEG/RAD switch, trig, logs, powers, roots, memory and history.
- Percentage CalculatorA percentage calculator: of a number, as a share of a total, or back to the whole from a part, with the formula shown.
Last updated: